Showing posts with label pen making. Show all posts
Showing posts with label pen making. Show all posts

Monday, December 8, 2014

Nautical Pen kit

Nautical pen kit from Penn state industry.
I used a teak wood blank from the battleship deck, USS  North Carolina. I bought the blank from woodcraft.

Saturday, October 31, 2009

Microwave drying wood pen blanks

The method I use to dry green pen blanks is microwave drying of the pen blanks.

When I need to dry pens blanks in a very short time, I use the following method.

I have a small Microwave oven I use only for drying wood. I do not use the microwave in the kitchen. I don't think my wife would be very happy if I did.


1. I cut the blanks into blank size usually 3/4" X 5" long.

2. I stack these in a way the air will flow freely around the blank.

3. I weight each blank and write the weight on the side of the blank. I use a digital postal scale. I picked up a scale off ebay for about $25

4. I place 8-9 blanks in the microwave in this fashion.

5. I microwave the blanks on low heat for 2 1/2 minutes.

6. I remove the blanks and the set on top of the microwave to cool.

7. They need to cool for 7-10 minutes.

8. I then weight the blanks again and write new weight on side

9. I go through this process a minimum of 3 times or until these is no longer a weight lost.

10. At this point I let set over night before processing the pen blanks.


Note; the microwave will set the blanks on fire, from the inside.
As you can see from the picture at the right. This blank caught on fire from the inside. I cut it apart and you can see how it burned.
Microwave drying will work must be done with care.
I used this to dry wood for 200 pens. I used this on maple wood blanks that had just been cut.
Please visit my web site for more woodworking infromation. http://nokeswoodworks.com

Saturday, February 14, 2009

Sedona Pen Kit made with Gemstone Blank

Sedona Rollerball Pen Kit


This is a silver plated rollerball pen kit. I used a Turquoise with black web Gemstone blank. I am please with how it turn
ed out. The Gemstome black was easy to drill and easy to turn. There are a little on the expensive side $8.99 per blank, but in this case well worth the
money. The blank was finished using micro mesh sanding pads up to 32000 grit. I then used a light coat of wax. This makes a great pen.
Please visit my web site : http://nokeswoodworks.com/

Monday, January 26, 2009

Pen Blank Drilling Jig Basic Homemade


Here is a basic homemade pen blank drilling jig I made. Its not fancy but it gets the job done.

I took two pieces of 1 1/2" X 1 1/2" wood 8" long. I joined them using a 1"X 1" hinge. To form a vise. I then marked two sets of vee notches in the wood. Using my bandsaw I cut out the notches.

The 1st vee notch is slightly smaller than 5/8" and the 2nd is slightly smaller than 3/4". These are the normal size for pen blanks. Using the notched to center and the vise like hinge to hold, I can drill a pen blank in no time at all and it will be straight and square. You can buy pen blanks and pen kits at woodcraft by clicking on the link to the right.

Please visit my web site for more information and tips on pen making, bowl turning and woodworking in general. http://nokeswoodworks.com

Sunday, May 11, 2008

Pen Kit Finish Notes

Notes about pen kit finishes:

24kt Gold Pens with 24k gold plating usually wear very quickly most have a coating of epoxy on them to help extend the wear life of the pen.

10k Gold pens with 10k gold plating wear better because the gold is mixed with hard nickel to form a more durable gold plating with is also cheaper. wears better than 24k gold.

Chrome pens, Chrome is used where there is alot of everyday use such as key rings, very durable and looks great at cheap price. Chrome is very shiny and very good looking. Wears better than 24k or 10 k gold

Black chrome. These are pens plated with a black color plating. The black has a soft sheen which is attractive against light color woods. It is more durable the 24k gold but less durable than 10k gold.

Satin pens get a plating that is a matte finish and gives a satin look to the pens, The finish has a slight texture to the feel of then. This more durable than 24k gold and less then 10k gold slightly more durable than black chrome.

Black Titanium pens are coated with a titanium plating which looks good and is very wear resistance. This finish give one of the most durable finished to pens.

Rhodium plated pens are the top of the line and the best looking pen kits available on the market there durable is equal to or better than Titanium. The appearance is the great.

For more information on pens please visit my web site: http://nokeswoodworks.com

Randy

Friday, May 9, 2008

Pen Making Abalone Kit


This is a Wallstreet II Tropical Isle Abalone Kit from Woodcraft. I did this kit as a Mother's day gift for my wife. The kit came with the hole already drilled and the brass tube inserted. The polyester resin the Abalone is sealed is more difficult to turn than normal acrylic blanks. The polyester resin can easily chip. Sharp tools must be used. During the turning process, the blank on this pen chipped out near the edge. I used a small file while the lathe was on to soften the rough edges before continuing to turn the blank .

I finished turning the pen blank and then completed it in the normal way using sand paper. I buffed the blank to a final shine and assembled the pen using a pen press. For more pictures on this project please visit my web site.
Randy









Sunday, April 27, 2008

Carbara Pen Kit using a Rattlesnake Blank

Rattlesnake Pen
I used a rattlesnake pen blank and a Black Titanium Carbara Pen kit to build this rattlesnake pen. These blanks are more difficult to turn compared to wood or regular acrylic. Care must be taken because the acrylic can be easily lifted off the surface of the snakeskin because of the chemicals used to tan the snake hides. Sharp tools must be used.
The blanks come with the brass tube already inside the skin and acrylic. Therefore you do not need to drill and glue the brass tube.
You will however have to size the blank and square the ends. The sides of the blanks are also removed during the sanding process. See the drawing that came with the blank for this detail.

The edges were sanded and the blank was placed on the lathe. I used a spindlemaster lathe tool to turn the blank down to size. The lathe tools must be extremely sharp. I stopped 4 times to hone the tool while cutting the blank to size. I stopped cutting short of the bushing size. Sandpaper was used to complete the projects. I used micro mesh and an acrylic finish to complete the blank. The blank was assembled using a pen press. More ideas can be seen at my web site:
http://nokeswoodworks.com/

The rattlesnake blank and pen kit came from: Arizona Silhouette at http://ArizonaSilhouette.com .



Sunday, April 20, 2008

Pen Making The Wall Street II Pen kit

Wall Street II Pen kit from Woodcraft.

The following pictures may be helpful in understanding the steps needed to build the Wall Street pen kit that I purchased from Woodcraft. The finished pen is illustrated here to the right. These are easy pens for the beginner and fun for the experienced turner as well. I used my Jet mini lathe and Robert Sorby turning tools.

The picture to the left shows the pen kit parts, drill bit 27/64 , the wood blank and the epoxy used to make the pen kits. The first Step is to cut the blank to length. Use the brass tube to measure and mark the blank for cutting. Cut the blank a little longer than the brass tube. It will be made to length later. Mark the center of the blank on the end before drilling. Drill slowly and clean out drill bit often. If you get the blank too hot or do not clean out the bit you will get a blow out on the blank. As you can see in the picture I have a home made pen vise that I have used successfully for years.


After the pen blank is drilled. I sand the brass tube lightly before mixing epoxy to glue the tube inside the blank. I like epoxy more than CA glue, but CA glue will work fine also. After the pen blank has dried I then go to the sander to square up the ends. A picture of this process can be seen on my web site: http://nokeswoodworks.com/


Once the ends are square, It is ready to be mounted on the lathe using a bushing and a pen mandrel. The picture to the right shows the pen blank mounted to the lathe .


Once the blank is mounted to the lathe, and everything is tightened up. The blank is then ready to be turned. Refer to my blog on lathe speeds for correct turning speed for pens or other projects. There are pictures of the actual turning process on my web site. A gouge is used to reduce the pen blank to a rough round size. A skew is then use to take the blank to proper size. I use the spindle master instead of a skew. This smooths the blank and gets it to the right size ready for sanding. I use a range of sand paper from 120 to 600 and then use micro mesh to 6000 for the sanding process. Once this is complete I use a finish of my choice. In this case I used Hut crystal coat to finish this pen. This is a friction polish and is applied with a cotton cloth and rubbed into the wood while the lathe is running. Once the finish is complete the pen blank is removed from
the lathe. It is assembled using a pen vise. Please visit my web site for more pictures and more information on pen making. http://nokeswoodworks.com/

This kit can be purchased from Woodcraft. See link to the right.







































Monday, March 24, 2008

Tips for buying a Mini Lathe for wood turning

The use of a mini lathe to turn wood projects has become an extremely popular hobby for both money making and enjoyment. If you are looking to purchase a mini lathe, here are a few points to consider.
Decide what projects, you will want to make, this will help determine if a mini lathe is right for you. Mini lathes are great for pen making, wine stopper making, small bowls or plates, tool handles. Christmas decorations, small table legs, small turned boxes.
There are a lot of brands of mini lathes out here which will do a good job. My lathe is a JET which I am very happy with. I have had it for a number of years and it has been put to good use and worked well.
The things I would look for in a wood lathe are as follows:
a. Good speed range from 500 to at least 3000 RPM's.
b. MT-2 headstock and tail stock taper, there are more add-ons that fit this size.
c. Spindle nose of 1X8 TPI.
d. Cast iron bed.
e. 1/2 HP or better.
One thing that is a must when buying a lathe is make sure the head stock and tail stock line up perfectly. Check it the store if you can, or as soon as you get it home. If it does not line up take it back. You can check alignment buy putting a center in the head stock and tail stock. Pull the tail stock up close to the head stock and make sure they align.
Variable speed is nice but not necessary. Changing speed on the belt drive is not hard and there is one less electronic thing to go wrong.
Indexing head is a nice feature which can be used to enhance lathe projects but again is not necessary feature for a lathe.
Make sure to have sturdy place to mount the lathe. You will want as little vibration as possible. Make sure you buy a face shield when you buy the lathe. Buy the best tools you can afford to buy. Visit my web site for more information.
http://nokeswoodworks.com/

Thursday, March 6, 2008

Chisels used on the mini lathe to make pens

Which lathe tools do you use to turn pens on your mini lathe? There are four main chisels I use when turning pens.
1. A parting tool 1/8"
2. A roughing gouge 3/8"
3. A. Skew 1/2"
The 4th tool is more a choice than something you really need.
4. A spindlemaster by Robert Sorby tools.
All tools should be made of (HSS) high speed steel, they will stay sharp longer and will have less heat build up. I use a Delta slow speed grinder to sharpen my tools.
And you will need sharp tols if you every turn plastic pen blanks.
Let's go back to the spindlemaster, I have both the 1/2" version and the micro version. The micro version has become one of my favorite tool for turning pens and other small projects. The advantages over the skew are: easy of use, no sharp corners to dig in, it will plane, cut coves and beads and it is easy to sharpen.
Randy
http://www.nokeswoodworks.com

Saturday, March 1, 2008

Lathe Speed, Pen Making and Bowl Turning

What speed should you set your lathe to when turning different projects.
I have guidelines that I use when selecting what lathe speed to use. The speed you use should allow the blanks to turn with little or no vibration. So if you turn the lathe on and there is vibration, shut it down and lower the speed.
I always wear a face shield, which is a good safety practice.
My guidelines for turning wood are as follows:
Pen Turning 3000 RPM or higher
Stock smaller than 2" can turn at 3000 RPM
Stock which is 3" can turn at 2000 to 2800 RPM
Stock which is 5" can turn at 1200 to 1800 RPM
Anything over 6" should be turned at less than 1000 RPM
When sanding I always slow my lathe down to 500-600 RPM
When applying finish, I set it to it's lowest speed. Which for me is 500 RPM
These guidelines are for wood, if you turn other material, these may not be right for you.
These are only guides, try different things and see what works best for you.
Always wear a face shield or at least safety glasses when turning. And if it doesn't feel right shut it down. Do not turn wood with defects, cracks or knots.
http://nokeswoodworks.com/

Thursday, February 28, 2008

Pen Making and other Mini Lathe Projects

A mini lathe is great for Pen turning. I have a Jet mini lathe I use for all of my turning and woodworking. In addition to turning pens on my lathe I have also made the following projects.
1. Wine stoppers
2. Small bowls
3. Candle Holders
4. Tables legs for shaker tables (can be seen on mt web site)
5. Small birdhouses
6. Knobs for other woodworking projects
7. Tool handles
8. Duck call
9. Lidded boxes
10. Key rings
11. Small plates
12. Doll house furniture
I'm sure there are other items but this list may give you an idea of what a small lather can be used for. I have an extension for my lathe but rarely use it. In fact the only times I have used it, is in turning table legs and one time I made a cane. So an extension is not something I would buy right away. Be careful with a mini lathe, it can become addictive.
http://www.nokeswoodworks.com/

Sunday, February 24, 2008

Pen Making with plastic blanks

Plastic Blanks
When drilling blanks made with acrylic plastic, you will need to go very slow or the plastic will melt and clog. This could cause the blank to split.The drill bit needs to be very sharp or you may tend to oval the top of the hole. I like to use a twist drill on plastic blanks. A brad point bit is my favorite on wood but on plastic the brad point seems to skate around a lot.

I have switched to epoxy for gluing the brass to the pen blank but gap filling CA glue will work as well.

I sometime use a sander to round the blanks prior to putting them on the lathe. It seems to help a little.

One again when on the lathe, you must use very sharp tools. The sharper the better.
Please visit my web site for more information.
http://nokeswoodworks.com

Thursday, February 21, 2008

Drill Bits, A quick run down


Drill Bits
There are several types of drill bits out on the market today. The drill bit on the left is a twist bit and comes in steel which is inexpensive but does not stay sharp very long. You can also get these in High speed steel (HSS) which will last much longer. You can also get them titanium coated and carbide tipped which will both last longer but cost alot more. The next bit is a brad point bit which prevents skating and has wide flutes keeping it cooler longer. These are my favorite bits for drilling in wood. Especially wood pen blanks. The third bit is a bullet point drill bit, the ones I have are from Dewalt. These are also very good bits for drilling in wood and I would highly recommend for all wood projects even pen blank drilling.
The 4th bit shown above is a forstner drill bit. Used for drilling plug holes, clock inserts or any where a flat bottom hole is needed. The last bit pictured is a spade bit, used for drilling wood. I don't use this type bit very often. It is something I use if I have to drill a hole in a 2x4 to pass wire through.
The most common drill bit is the twist bit, which is very versatile and when purchased in HSS is a good all round bit.
Please visit my web site under general for more information on drill bits.
http://nokeswoodworks.com

Saturday, February 16, 2008

New Laptop Sony CR320 UPDATE

Update, 2 months later...this is the best laptop I have ever had.

Update 3 weeks later, I am still very happy with this computer. Works well, and looks good, very stylist. I have found one good/bad thing. The graphics board is a little light for game players. My son wanted to use it to play a new game and the graphics board would not handle it. So that is bad but it's good for me. I have the computer all to myself. It does handle all my graphic needs. I run corel draw and paint on my computer with no problems at all. I also tun google sketch up with no problems. So yes I still really like it. Visit the offical sony site to get more specs. There is a link to the right.
http://nokeswoodworks.com
Well I finally broke down and bought a new laptop. I really looked around before deciding on a Sony and now that I have it at home. WOW it is great. It did take a little while fr me to remove all of the unwanted software and install what I really needed and wanted but now that I have it in going, I couldn't be more excited about a computer. It seems to be study and well build has plenty of speed and disk storage. So now maybe I can get a few more blogs outs. I got a Sony camera for Christmas and this new laptop has a slot for the camera card, so maybe I'll get a few more pics on here as well. I know this is off the subject of woodworking but if you need a new computer, I would highly recommend this computer. I have placed an amazon ad in the section to the right, you can go there and see all the specs. In the next few weeks I will be adding a page to my website about building web sites and doing blogs.
So check out my web site. http://nokeswoodworks.com

Wednesday, February 13, 2008

PEN MAKING TIP

Sometimes when I turn an acrylic blank, the brass tube shows through on the finish turned pieces. If the blank is say black and white and the brass shows through the white, it does'nt look very good.
There is a way around this problem. You have to paint the brass tube before gluing it in place. Yes you can paint the brass tubes. You need to sand the outside of the tube with sandpaper. Make sure you sand the entire tube. I then use a wire inserted through the tube and bent at the end to hold the tube. I then use spray paint to paint the tube, then hang the other end of the wire up till it dries. Use a spray paint for metal like Rustoleum. Use a color of paint that matches the lighter color in the blank.
Once the paint has dried, you can glue it in normally. I use an expoy glue, seems to work better for me than CA.
Please see my website for information on pen making. http://www.nokeswoodworks.com

Sunday, February 10, 2008

New Pens, pen making



Just wanted to share a couple of new pens I made. The

ones on the outside are made with Rosewood. The center Pen is made of acrylic plastic. These pens look great and have a nice feel to them when writing. These are one piece pens which require a longer blank but only one blank. These are a great starter pen even tho most people start out with a slim line pen.

I have added a lot of new links to my web site and will being adding alot more so feel free to stop in and see, as if grows. http://nokeswoodworks.com

Tuesday, February 5, 2008

New Woodworking Web Site

Well, I am now starting my own web site in addition to doing a blog. In my new web site, I will try to cover alot about woodworking, furniture making, pen making, toy making, carving, scroll saw and home repair. As well as the home shop. Please let me know if there are pages you would like to see or information you would like to have. I am just starting so I have alot of pages to built and a lot of work to do on the site. So keep checking back. I will be updating it as often as I can.
The address for my new site is www.nokeswoodworks.com

I'd love to hear from you.

Saturday, February 2, 2008

Buying wood cheap for projects or Pens

If you havn't noticed wood is expensive. Here are a few tips on buying wood that have helped save me money.
1. Shorts - I buy from a company on the web called Wall lumber. They sell usp bundles which are 20bf feet and include shipping to my home. They also sell what they call shorts. They sell shorts in cherry, walnut, oak and maple. The shorts are boeard which range from 36" to 52" in lenght of random width. These are great for small projects and the cost is half the price of regular lumber.
2. Lumber grade - I sometimes buy number 2 grade instead of number one. The big difference is that number 2 will have a few knots ot sap wood. On some projects I can cut around that or may even built it into my project.
3. While shopping on ebay for lumber, which is the best place to buy reclaimed chestnut, one of my favorite woods. I can across a local cabinet shop selling cherry, at great prices. I bought some and now when in need of wood, i drive by the cabinet shop and see what they have to offer. Wood can be 60 % od regular pricing.
4. As you can tell , I do shop the internet for wood also. I use ebay, and other wood sources on the internet will offer deals from time to time.
5. Use a lower grade of lumber for hidden parts such as drawers or backs or framework. I often use popular for these parts instead of cherry or oak.
6. A local saw mill can be a source for cheap lumber also. Since you are buying wholesale and not retail. I even found one who through out the spalted lumber because it was no good for the flooring he was producing.
7. Pen makers can save a ton buy cutting there own blanks. Larger boards or scarps from your last project can be cut into pen blanks saving a lot or even getting them free.

BEWARE shopping at the local home store will cost you and is not the place to shop for lumber used in furniture or pen making. It is great for 2x4's buy try buying an oak board..wow
I do buy some ply wood there, which I use in the drawer bottoms.

One place I had yet to find saving is the pen blank market for stabilized woods. These are my favorite to turn but also are very expensive. If any one has a cheap source please let me know.
Please visit my website for more information http://nokeswoodworks.com

Saturday, January 26, 2008

Pen Making as a craft business

One of my hobbies which I have turned into a sell-able craft is my pen making. Pens are made using a mini lathe to turn a block of wood or plastic to shape to hold the pen workings, which I buy as a kit. I will use this as an example of my costing process. Pen Kits can vary from $2.95 a kit to 59.95 a kit depending on what kind of pen you want to make. The pictures below are of cigar pens. The cost for this kit is $ 5.95. The wood blank will cost from $1.00 to 6.95 depending on type of wood or plastic. I will use $ 3.00 in this example. The pen kit is $5.95 plus $3.00 for the pen blank will total materials of $8.95. It will take me 1/2 hour to make this pen at $15.00 per hour labor. Now my labor and material total $16.45. I them add overhead and profit. I figure my overhead and profit to be the same as material and labor which is $16.45. This give me a total selling price of $32.90. I i always throw in a case and sell them for $34.95. I have pens which sell for more and I have pens which sell for less.
Please visit my website for more woodworking and craft information
http://nokeswoodworks.com