Showing posts with label turning. Show all posts
Showing posts with label turning. Show all posts

Monday, June 2, 2008

Making Wine Stopper or Bottle Stopper kits,Stainless steel

WINE or BOTTLE STOPPER KITS




I recently purchased some stainless steel bottle stoppers from Arizona Silhouette. The wine stoppers are made of stainless steel and should not corrode for any reason. These are the best kits on the market
The wood is turned in the usual way. I drilled and tapped the hole to create threads on which the stopper could be mounted. The tap was sized at 3/8" to fit the stopper.
Here are some of the pictures from my new stoppers.
Please visit my web site for more on turnings with a mini lathe
http://nokeswoodworks.com/






Sunday, April 20, 2008

Pen Making The Wall Street II Pen kit

Wall Street II Pen kit from Woodcraft.

The following pictures may be helpful in understanding the steps needed to build the Wall Street pen kit that I purchased from Woodcraft. The finished pen is illustrated here to the right. These are easy pens for the beginner and fun for the experienced turner as well. I used my Jet mini lathe and Robert Sorby turning tools.

The picture to the left shows the pen kit parts, drill bit 27/64 , the wood blank and the epoxy used to make the pen kits. The first Step is to cut the blank to length. Use the brass tube to measure and mark the blank for cutting. Cut the blank a little longer than the brass tube. It will be made to length later. Mark the center of the blank on the end before drilling. Drill slowly and clean out drill bit often. If you get the blank too hot or do not clean out the bit you will get a blow out on the blank. As you can see in the picture I have a home made pen vise that I have used successfully for years.


After the pen blank is drilled. I sand the brass tube lightly before mixing epoxy to glue the tube inside the blank. I like epoxy more than CA glue, but CA glue will work fine also. After the pen blank has dried I then go to the sander to square up the ends. A picture of this process can be seen on my web site: http://nokeswoodworks.com/


Once the ends are square, It is ready to be mounted on the lathe using a bushing and a pen mandrel. The picture to the right shows the pen blank mounted to the lathe .


Once the blank is mounted to the lathe, and everything is tightened up. The blank is then ready to be turned. Refer to my blog on lathe speeds for correct turning speed for pens or other projects. There are pictures of the actual turning process on my web site. A gouge is used to reduce the pen blank to a rough round size. A skew is then use to take the blank to proper size. I use the spindle master instead of a skew. This smooths the blank and gets it to the right size ready for sanding. I use a range of sand paper from 120 to 600 and then use micro mesh to 6000 for the sanding process. Once this is complete I use a finish of my choice. In this case I used Hut crystal coat to finish this pen. This is a friction polish and is applied with a cotton cloth and rubbed into the wood while the lathe is running. Once the finish is complete the pen blank is removed from
the lathe. It is assembled using a pen vise. Please visit my web site for more pictures and more information on pen making. http://nokeswoodworks.com/

This kit can be purchased from Woodcraft. See link to the right.







































Monday, March 24, 2008

Tips for buying a Mini Lathe for wood turning

The use of a mini lathe to turn wood projects has become an extremely popular hobby for both money making and enjoyment. If you are looking to purchase a mini lathe, here are a few points to consider.
Decide what projects, you will want to make, this will help determine if a mini lathe is right for you. Mini lathes are great for pen making, wine stopper making, small bowls or plates, tool handles. Christmas decorations, small table legs, small turned boxes.
There are a lot of brands of mini lathes out here which will do a good job. My lathe is a JET which I am very happy with. I have had it for a number of years and it has been put to good use and worked well.
The things I would look for in a wood lathe are as follows:
a. Good speed range from 500 to at least 3000 RPM's.
b. MT-2 headstock and tail stock taper, there are more add-ons that fit this size.
c. Spindle nose of 1X8 TPI.
d. Cast iron bed.
e. 1/2 HP or better.
One thing that is a must when buying a lathe is make sure the head stock and tail stock line up perfectly. Check it the store if you can, or as soon as you get it home. If it does not line up take it back. You can check alignment buy putting a center in the head stock and tail stock. Pull the tail stock up close to the head stock and make sure they align.
Variable speed is nice but not necessary. Changing speed on the belt drive is not hard and there is one less electronic thing to go wrong.
Indexing head is a nice feature which can be used to enhance lathe projects but again is not necessary feature for a lathe.
Make sure to have sturdy place to mount the lathe. You will want as little vibration as possible. Make sure you buy a face shield when you buy the lathe. Buy the best tools you can afford to buy. Visit my web site for more information.
http://nokeswoodworks.com/

Sunday, March 9, 2008

Wine Stopper or Bottle Stopper

Turning a wine or bottle stopper is similar to turning a pen. Use the same lathe, same turning tools.

Start with a blank of wood 1 1/2" X 1 1/2" X 2".
This will be placed in a drill press vise ready to drill, you may want to start with a Foster 3/4" drill bit to recess
the hole depending on type bottle stopper you are using. If you do recess the hole, then center Fostner bit on
the blank and drill down 3/8 of an inch.
Next insert a 6mm drill bit and drill down 1". This will be the first step if you decide not to recess the hole.

You will need a bottle stopper mandrel, attach the mandrel to the head stock. Then screw the stopper onto the
mandrel using the 6 mm hole just drilled. Now pull up the tail stock and tighten to secure.

Using a skew and spindle gouge turn the stopper to desired shape. Sizes and shapes may vary.
Remove tail stock and finish turning. I use a spindle master for most of my turning work.

Now sand using progressive grits of sand paper to 600 grit. Apply finish, this can be wax, sanding sealer, wood
turners wax or a CA finish.

Remove the turned piece and glue the head to the stopper with thick CA glue. I always use epoxy

There are a couple of different types of stainless steel stopper. Some people use a dowel in the hole and glue a
cork to the other end. See my web site for more on turning.

Randy
http://nokeswoodworks.com

Thursday, February 28, 2008

Pen Making and other Mini Lathe Projects

A mini lathe is great for Pen turning. I have a Jet mini lathe I use for all of my turning and woodworking. In addition to turning pens on my lathe I have also made the following projects.
1. Wine stoppers
2. Small bowls
3. Candle Holders
4. Tables legs for shaker tables (can be seen on mt web site)
5. Small birdhouses
6. Knobs for other woodworking projects
7. Tool handles
8. Duck call
9. Lidded boxes
10. Key rings
11. Small plates
12. Doll house furniture
I'm sure there are other items but this list may give you an idea of what a small lather can be used for. I have an extension for my lathe but rarely use it. In fact the only times I have used it, is in turning table legs and one time I made a cane. So an extension is not something I would buy right away. Be careful with a mini lathe, it can become addictive.
http://www.nokeswoodworks.com/

Sunday, February 10, 2008

New Pens, pen making



Just wanted to share a couple of new pens I made. The

ones on the outside are made with Rosewood. The center Pen is made of acrylic plastic. These pens look great and have a nice feel to them when writing. These are one piece pens which require a longer blank but only one blank. These are a great starter pen even tho most people start out with a slim line pen.

I have added a lot of new links to my web site and will being adding alot more so feel free to stop in and see, as if grows. http://nokeswoodworks.com

Tuesday, January 22, 2008

Bandsaw

The Bandsaw is the most overlooked tool in the shop. My bandsaw has become a do everything machine. I use it many times instead of my tablesaw. Especially for smaller projects. Its the tool of choice anytime I am cutting curves. I use it to make some cuts on dovetails. I use it to trim pen blanks to size. I also use it for Bandsaw boxes. It can resaw thick wood to give me the thin wood I need for small projects. Its great when making pen boxes or candle boxes. I have even used it to cut table legs.
My bandsaw is the Jet 12" floor model. Most people go for the 14" model but to date the 12" model has done a great job.
Any time I want to prepare wood for the lathe for bowl making my first stop is the bandsaw.
For me the bandsaw is a must have tool in the shop.
Please visit my web site for more information http://nokeswoodworks.com

Sunday, January 13, 2008

Pen Making Pictures


Here is a picture of some of my pens.
These are all Cigar pens.

Wednesday, January 9, 2008

Pen Making

PEN MAKING

One of my favorite woodworking projects is Pen Making.
The Tools required to make Pens are as follows:

1. Lathe .... I have a Jet Mini Lathe and it is perfect for pen making.
2. Lathe Tools You will need a 1/2 Gouge for rough cutting, a skew chisel for fine details and Parting tool for making tendons.
3. Pen mandrel This holds the pen blacks between centers while turning
4. Pen Bushings These are used to hold blanks but more for sizing the blanks. You will turn the wood down to the size of these bushings. There are different size bushing for different size or kinds of pens.
5.Barrel trimmer used to square up the ends of the wood before putting on the mandrel. A disk sander can be used instead of a barrel trimmer.
6. CA glue (super glue) or epoxy used to glue the brass barrel into the wood body.
7. You can buy blanks already pre drilled but if you cut your on, you will need the following:
Drill press, Vise to hold blank while drilling, drill bit (7mm for slim line kit), ans saw for cutting blanks to size.
8. Sanding paper 150-1000 grit
9. wax finish like HUT or Shellwax
10. Pen Kits, there are alot of pen kits out there most people start with a slim line kit.
these kits contain all the pen parts you need except for the wood.

Once you have everything.. you follow these easy steps:

Cut blanks to size for slim line 5/8" square and cut to the length of the brass tube plus an 1/8 inch used to square up blank later.
Drill Hole in the blanks 7mm for slimline kits. this hole must be drilled down the center of the blanks.
Apply glue to the brass blank and insert it into the freshly drilled blanks. You may want to sand the brass tube lightly to get better adhesion of the glue.
Once dry, square up the blanks using a barrel trimmer or disk sander.
Now put the mandrel on the lathe, put one bushing on then one pen blank, a bushing, the second pen blank and another bushing. Now move up an tighten tail stock with live center.
Begin turning the stock until you have the size and look you want. the ends should be turned to the size of the bushing. Well almost leave a tiny amount for the sanding process.
Sand while lathe is running fro 150 to 1000 grit paper.
You are now ready to apply wax for a finish.
Once this is done take the completed wood blanks and using a vise or pen press. Press the pen parts on to the wood blanks.
You now have a completed pen.