Showing posts with label Handmade pens. Show all posts
Showing posts with label Handmade pens. Show all posts

Saturday, October 3, 2009

Pen Project with Cross Clip for Church



I just finished doing a project for a church. The church was expanding and had to cut down a Maple tree. They contacted me and wanted me to make 200 pens for them.



I used a slimline kit for the base. I added a fancy center band and a cross clip from Woodcraft.

I made a sample and we agreed on a price, the church shipped the wood to me. It arrived on a banded pallet, which consisted mainly of cut up logs. I had to take the logs and cut the logs into pen blanks.


As you can see from the picture at the right, the shipment basically looked like a load of fire wood. Some of the logs were pretty big. I split the logs and then used my band saw to cut the wood into rough pen blanks.




The rough pen blanks were dried by stacking them and air drying along with the use of a micro wave oven to air dry the blanks.




Once the blanks were dry, there were cut, drilled and turned to shape. There were sanded and finished with a protective coating.


The pens were assembled and packed in plastic pen cases and shipped to the church.


The church was very please upon receipt of the pens. There was a lot of work involved in making 200 pens at one time but I enjoyed the project.
If you have a project you would like made from a special piece of wood or any custom project, please contact me.
Also visit my web site at http://nokeswoodworks.com/

Monday, January 26, 2009

Pen Blank Drilling Jig Basic Homemade


Here is a basic homemade pen blank drilling jig I made. Its not fancy but it gets the job done.

I took two pieces of 1 1/2" X 1 1/2" wood 8" long. I joined them using a 1"X 1" hinge. To form a vise. I then marked two sets of vee notches in the wood. Using my bandsaw I cut out the notches.

The 1st vee notch is slightly smaller than 5/8" and the 2nd is slightly smaller than 3/4". These are the normal size for pen blanks. Using the notched to center and the vise like hinge to hold, I can drill a pen blank in no time at all and it will be straight and square. You can buy pen blanks and pen kits at woodcraft by clicking on the link to the right.

Please visit my web site for more information and tips on pen making, bowl turning and woodworking in general. http://nokeswoodworks.com

Sunday, May 11, 2008

Pen Kit Finish Notes

Notes about pen kit finishes:

24kt Gold Pens with 24k gold plating usually wear very quickly most have a coating of epoxy on them to help extend the wear life of the pen.

10k Gold pens with 10k gold plating wear better because the gold is mixed with hard nickel to form a more durable gold plating with is also cheaper. wears better than 24k gold.

Chrome pens, Chrome is used where there is alot of everyday use such as key rings, very durable and looks great at cheap price. Chrome is very shiny and very good looking. Wears better than 24k or 10 k gold

Black chrome. These are pens plated with a black color plating. The black has a soft sheen which is attractive against light color woods. It is more durable the 24k gold but less durable than 10k gold.

Satin pens get a plating that is a matte finish and gives a satin look to the pens, The finish has a slight texture to the feel of then. This more durable than 24k gold and less then 10k gold slightly more durable than black chrome.

Black Titanium pens are coated with a titanium plating which looks good and is very wear resistance. This finish give one of the most durable finished to pens.

Rhodium plated pens are the top of the line and the best looking pen kits available on the market there durable is equal to or better than Titanium. The appearance is the great.

For more information on pens please visit my web site: http://nokeswoodworks.com

Randy

Sunday, April 27, 2008

Carbara Pen Kit using a Rattlesnake Blank

Rattlesnake Pen
I used a rattlesnake pen blank and a Black Titanium Carbara Pen kit to build this rattlesnake pen. These blanks are more difficult to turn compared to wood or regular acrylic. Care must be taken because the acrylic can be easily lifted off the surface of the snakeskin because of the chemicals used to tan the snake hides. Sharp tools must be used.
The blanks come with the brass tube already inside the skin and acrylic. Therefore you do not need to drill and glue the brass tube.
You will however have to size the blank and square the ends. The sides of the blanks are also removed during the sanding process. See the drawing that came with the blank for this detail.

The edges were sanded and the blank was placed on the lathe. I used a spindlemaster lathe tool to turn the blank down to size. The lathe tools must be extremely sharp. I stopped 4 times to hone the tool while cutting the blank to size. I stopped cutting short of the bushing size. Sandpaper was used to complete the projects. I used micro mesh and an acrylic finish to complete the blank. The blank was assembled using a pen press. More ideas can be seen at my web site:
http://nokeswoodworks.com/

The rattlesnake blank and pen kit came from: Arizona Silhouette at http://ArizonaSilhouette.com .



Sunday, April 20, 2008

Pen Making The Wall Street II Pen kit

Wall Street II Pen kit from Woodcraft.

The following pictures may be helpful in understanding the steps needed to build the Wall Street pen kit that I purchased from Woodcraft. The finished pen is illustrated here to the right. These are easy pens for the beginner and fun for the experienced turner as well. I used my Jet mini lathe and Robert Sorby turning tools.

The picture to the left shows the pen kit parts, drill bit 27/64 , the wood blank and the epoxy used to make the pen kits. The first Step is to cut the blank to length. Use the brass tube to measure and mark the blank for cutting. Cut the blank a little longer than the brass tube. It will be made to length later. Mark the center of the blank on the end before drilling. Drill slowly and clean out drill bit often. If you get the blank too hot or do not clean out the bit you will get a blow out on the blank. As you can see in the picture I have a home made pen vise that I have used successfully for years.


After the pen blank is drilled. I sand the brass tube lightly before mixing epoxy to glue the tube inside the blank. I like epoxy more than CA glue, but CA glue will work fine also. After the pen blank has dried I then go to the sander to square up the ends. A picture of this process can be seen on my web site: http://nokeswoodworks.com/


Once the ends are square, It is ready to be mounted on the lathe using a bushing and a pen mandrel. The picture to the right shows the pen blank mounted to the lathe .


Once the blank is mounted to the lathe, and everything is tightened up. The blank is then ready to be turned. Refer to my blog on lathe speeds for correct turning speed for pens or other projects. There are pictures of the actual turning process on my web site. A gouge is used to reduce the pen blank to a rough round size. A skew is then use to take the blank to proper size. I use the spindle master instead of a skew. This smooths the blank and gets it to the right size ready for sanding. I use a range of sand paper from 120 to 600 and then use micro mesh to 6000 for the sanding process. Once this is complete I use a finish of my choice. In this case I used Hut crystal coat to finish this pen. This is a friction polish and is applied with a cotton cloth and rubbed into the wood while the lathe is running. Once the finish is complete the pen blank is removed from
the lathe. It is assembled using a pen vise. Please visit my web site for more pictures and more information on pen making. http://nokeswoodworks.com/

This kit can be purchased from Woodcraft. See link to the right.







































Sunday, March 2, 2008

Woodworking and Crafts, sell on line at Etsy.com

Ae you looking for a place online to sell your woodworking, pens or other crafts without actually setting up a web page? Well the anwser might me a web site called http://www.etsy.com/ . Etsy has been around since 2005 and is an online make place for buying and selling all things hand made. Over 100,000 sellers worldwide have opened shop. Etsy really is a cool place to sell your crafts and it's easy to use. There are lots of categories to sell your goods. A few are candles, jewelry needlecrafts, quilts, pets, toys, supplies and woodworking.
Make sure you read and follow there terms of use.
http://www.nokeswoodworks.com

Sunday, February 24, 2008

Pen Making with plastic blanks

Plastic Blanks
When drilling blanks made with acrylic plastic, you will need to go very slow or the plastic will melt and clog. This could cause the blank to split.The drill bit needs to be very sharp or you may tend to oval the top of the hole. I like to use a twist drill on plastic blanks. A brad point bit is my favorite on wood but on plastic the brad point seems to skate around a lot.

I have switched to epoxy for gluing the brass to the pen blank but gap filling CA glue will work as well.

I sometime use a sander to round the blanks prior to putting them on the lathe. It seems to help a little.

One again when on the lathe, you must use very sharp tools. The sharper the better.
Please visit my web site for more information.
http://nokeswoodworks.com

Saturday, February 2, 2008

Buying wood cheap for projects or Pens

If you havn't noticed wood is expensive. Here are a few tips on buying wood that have helped save me money.
1. Shorts - I buy from a company on the web called Wall lumber. They sell usp bundles which are 20bf feet and include shipping to my home. They also sell what they call shorts. They sell shorts in cherry, walnut, oak and maple. The shorts are boeard which range from 36" to 52" in lenght of random width. These are great for small projects and the cost is half the price of regular lumber.
2. Lumber grade - I sometimes buy number 2 grade instead of number one. The big difference is that number 2 will have a few knots ot sap wood. On some projects I can cut around that or may even built it into my project.
3. While shopping on ebay for lumber, which is the best place to buy reclaimed chestnut, one of my favorite woods. I can across a local cabinet shop selling cherry, at great prices. I bought some and now when in need of wood, i drive by the cabinet shop and see what they have to offer. Wood can be 60 % od regular pricing.
4. As you can tell , I do shop the internet for wood also. I use ebay, and other wood sources on the internet will offer deals from time to time.
5. Use a lower grade of lumber for hidden parts such as drawers or backs or framework. I often use popular for these parts instead of cherry or oak.
6. A local saw mill can be a source for cheap lumber also. Since you are buying wholesale and not retail. I even found one who through out the spalted lumber because it was no good for the flooring he was producing.
7. Pen makers can save a ton buy cutting there own blanks. Larger boards or scarps from your last project can be cut into pen blanks saving a lot or even getting them free.

BEWARE shopping at the local home store will cost you and is not the place to shop for lumber used in furniture or pen making. It is great for 2x4's buy try buying an oak board..wow
I do buy some ply wood there, which I use in the drawer bottoms.

One place I had yet to find saving is the pen blank market for stabilized woods. These are my favorite to turn but also are very expensive. If any one has a cheap source please let me know.
Please visit my website for more information http://nokeswoodworks.com

Sunday, January 13, 2008

Pen Making Pictures


Here is a picture of some of my pens.
These are all Cigar pens.